Cary-Apex Water Treatment Facility Caustic Building Rehabilitation

1. Replace four 20,000-gallon FRP tanks with 20,000-gallon steel tanks suitable for storage of 50% caustic. All associated suction and discharge piping to require minor modifications as shown. 2. Modify fill piping so that caustic fill pipes are not overhead. New fill piping shall be HDPE. 3. Demolish existing cast iron floor drains replace with plastic floor drains. Floor slab demo and repair as required. 4. Prepare all containment area surfaces as required and install new containment coatings over the entirety of the containment areas. 5. Route new conduit and wire between any locations where there is existing conduit and wire in the slab and abandon the existing conduit and wire. New conduit and wiring is to be routed overhead via cable tray. Contractors offering a proposal on this project must be licensed to do the specified type of contracting in the State of North Carolina. All bids must include a non- collusive affidavit. Contractors offering a proposal on this project must comply, and must ensure that their subcontractors comply, with the requirements of Article 2 of Chapter 64 of the North Carolina General Statutes, "Verification of Work Authorization," and must provide documentation or sign affidavits or any other documents requested by the Town of Cary demonstrating such compliance. Each proposal shall be accompanied by a bid deposit in the amount of not less than five percent (5%) of the amount of the bid in the form and subject to the conditions provided in the Instruction to Bidders. The Town of Cary reserves the right to reject any or all proposals. Each proposal shall be accompanied by a Bid Bond payable to the Town of Cary for an amount of not less than five percent (5%) of the total amount bid; or in lieu of the Bid Bond, the bidder may offer the bid deposit in the form of a cashier's check, or a certified check on a bank or trust company insured by the FDIC. The bid bond must be executed by a corporate surety licensed in North Carolina. The bid deposit may be held for a period of sixty (60) days pending award of the contract. Notification of award of contract shall be evidence of intent to contract and shall extend time for holding the contractor's bid surety for a time mutually agreed between the Town of Cary and the bidder The award of the Contract, if it is awarded, will be to the lowest responsive, responsible bidder whose qualifications indicate the award will be in the best interest of the Town of Cary (Owner). The Town of Cary reserves the right to waive technicalities and/or reject any or all proposals. A Performance Bond and a Payment Bond, each in the amount of one hundred percent (100%) of the contract price, with a corporate surety approved by the Town of Cary, will be required for the faithful performance of the contract. Bidders shall provide certification that performance and payment bond sureties are licensed in North Carolina. All questions about the meaning or intent of the Contract documents shall be submitted in writing to Hazen and Sawyer, attention Kyle Thompson PE, at email address kthompson@hazenandsawyer.com. Replies will be issued by Addenda, mailed or delivered to all parties recorded by the Engineer as having received the Bidding Documents. Questions received less than five days prior to the date for opening of Bids may not be answered. Only questions answered by written Addenda will be binding. Oral and other interpretations or clarifications will be without legal effect. Addenda, when issued, will be on file at the offices of the Owner and Engineer at least twenty-four hours before bids are opened. It shall be the Bidder's responsibility to make inquiry as to the Addenda issued. All such Addenda shall become part of the Contract Documents and all Bidders shall be bound by such Addenda, whether or not received by the Bidders.

Division 02 -	Existing Conditions, Subsurface Investigation.
Division 03 -	Concrete, Concrete Reinforcing, Cast-in-Place Concrete, Precast Concrete.
Division 04 -	Masonry, Unit Masonry.
Division 05 -	Metals, Structural Metal Framing, Metal Decking, Metal Fabrications.
Division 06 -	Wood, Plastics, and Composites, Rough Carpentry.
Division 07 -	Thermal and Moisture Protection, Dampproofing and Waterproofing, Thermal Protection.
Division 08 -	Openings, Doors and Frames, Windows, Hardware.
Division 09 -	Finishes, Painting and Coating.
Division 10 -	Specialties, Signage, Compartments and Cubicles, Emergency Aid Specialties, Fire Protection Specialties, Storage Assemblies.
Division 11 -	Equipment, Laboratory Equipment.
Division 14 -	Conveying Equipment.
Division 21 -	Fire Suppression, Fire-Extinguishing Systems.
Division 22 -	Plumbing, Instrumentation and Control for Plumbing, Plumbing Piping, Plumbing Equipment, Plumbing Fixtures.
Division 23 -	Heating, Ventilating, and Air Conditioning (HVAC), Instrumentation and Control for HVAC, Facility Fuel Piping, Facility Fuel-Storage Tanks, HVAC Air Distribution.
Division 26 -	Electrical, Instrumentation and Control for Electrical Systems, Interior Lighting, Emergency Lighting, Exit Signs, Exterior Lighting.
Division 27 -	Communications, Structured Cabling, Data Communications, Voice Communications, Distributed Audio-Video Communications Systems.
Division 28 -	Electronic Safety and Security, Electronic Access Control and Intrusion Detection, Access Control, Intrusion Detection, Electronic Surveillance, Electronic Detection and Alarm.
Division 31 -	Earthwork, Clearing and Grubbing, Grading, Earthwork Methods.
Division 32 -	Exterior Improvements, Flexible Paving, Rigid Paving, Curbs, Gutters, Sidewalks, and Driveways, Fences and Gates, Turf and Grasses.
Division 33 -	Utilities, Water Utilities, Storm Drainage Utilities, Electrical Utilities, Communications Utilities.
Division 44 -	Pollution and Waste Control Equipment, Common Work Results for Pollution and Waste Control Equipment, Air Pollution Control, Noise Pollution Control, Odor Control, Water Pollution Control Equipment, Solid Waste Control and Reuse, Waste Thermal Processing Equipment, Fluidized Bed Combustion Equipment, Rotary Kiln Incinerators, Pyrolysis Equipment, Hazardous Waste and Medical Waste Incinerators, Heat Recovery Equipment for Waste Thermal Processing, Synthesis Gas Cleanup and Handling Equipment.