Jet A Fuel Tank - Soldotna

SYTEM DESCRIPTION: Tanks: 1. Provide one new double wall 500 gallon tank that will hold JET A aviation fuel. The tank system will be constructed to meet Fireguard Steel Tank Institute specifications. The tank shall be cylindrical in shape and mounted on structural steel beam skids that are an integral part of the tank with the proper nameplates for a supported tank system. 2. Several items listed in these specifications may be deviations from your standard tanks and therefore careful review of these specifications and close contact with the CO are very important. Provide ports for filling, suction, fuel quantity gauge, interstitial leak detection, one for normal venting of the primary tank, two for emergency venting of the primary and secondary tank and one spare port for the primary tank plugged with an approved cast iron plug and a frost proof drain valve. 3. Tank shall have ports that are raised and broadened such that there are no depressions around port openings, to prevent ice, snow or liquids from pooling around tank openings. 4. The total (actual) capacity of the tank shall neither be less than the rated nominal capacity nor more than 110 percent of the rated nominal capacity. 5. Provide lifting lugs and ground points. 6. Provide full detail information/details on available commercial standard warranty. 7. Provide full detailed information and commissioning instructions. Appurtenances: 1. Marine grade coating system, desert sand color 2. One (1) each normal vent pipe long enough to be twelve (12) feet above ground level. 3. One (1) each normal vacuum pressure vent set below the pressure of the emergency vents 4. Two (2) each emergency vent pipes long enough to be two feet above the top of the tank 5. Two (2) each emergency vacuum pressure vents set above the pressure of the normal vent. 6. One (1) each spill containment basin 7. One (1) each OSHA approved end mounted ladder 8. One (1) each interstitial leak detection indicator 9. One (1) each clock type battery powered alarming fuel quantity gauge 10. Fill and suction tubes The tank systems shall arrive as completely assembled and as ready for use as possible. The system shall be completely plumbed, prewired, and explosion proof. PROPOSAL DOCUMENTS With the proposal Contractor shall provide initial shop drawings and appurtenance data with sufficient details to prove they meet government requirements. Solicitation Questions Due: 8/13/2022 @ 1700 ET to emelia_flaherty@fws.gov

Division 03 -	Concrete, Concrete Forming and Accessories, Cast-in-Place Concrete.
Division 04 -	Masonry, Unit Masonry.
Division 06 -	Wood, Plastics, and Composites, Rough Carpentry, Finish Carpentry, Millwork.
Division 07 -	Thermal and Moisture Protection, Dampproofing and Waterproofing, Thermal Protection, Weather Barriers.
Division 08 -	Openings, Doors and Frames, Entrances, Windows.
Division 09 -	Finishes, Plaster and Gypsum Board, Acoustical Ceilings, Flooring, Carpeting, Acoustic Treatment, Painting.
Division 12 -	Furnishings.
Division 21 -	Fire Suppression, Water-Based Fire-Suppression Systems, Fire-Extinguishing Systems.
Division 22 -	Plumbing, Instrumentation and Control for Plumbing, Plumbing Piping, Plumbing Equipment, Plumbing Fixtures, Drinking Fountains and Water Coolers.
Division 23 -	Heating, Ventilating, and Air Conditioning (HVAC), Instrumentation and Control for HVAC, HVAC Air Distribution, Central HVAC Equipment.
Division 26 -	Electrical, Power Distribution Units, Lighting, Interior Lighting, Emergency Lighting, Exit Signs, Exterior Lighting.
Division 27 -	Communications, Structured Cabling, Data Communications, Voice Communications.
Division 28 -	Electronic Safety and Security.
Division 31 -	Earthwork, Clearing and Grubbing, Grading, Soil Treatment.
Division 32 -	Exterior Improvements, Flexible Paving, Asphalt Paving, Rigid Paving, Concrete Paving, Curbs, Gutters, Sidewalks, and Driveways, Paving Specialties, Parking Bumpers, Pavement Markings, Fences and Gates, Irrigation, Planting.
Division 33 -	Utilities.